lid

Hopefully you would of seen the black box that I 3D Printed the day before yesterday. There were a lot of things wrong with the box so Yesterday I decided to revamp it. To cut a long story short I made a right mess of it, I managed to sort the text out and put 2 sleeves inside the box to hold...

Made this little beauty with a bit of piercing on the lid for a bit of fun and it instantly sold

So I've not done much turning lately but here is my first attempt at a bowl with a lid... Regards Padster

Fully hollowed out to 5mm (ish). This Oak blank had been kicking about for ages so I thought I had better use it and make some space. The finial is Maple and the lid is some bit of scrap. I think it's all still moving a little but hopefully will settle down. Dare not take any more of the lid...

NOTE TO PHIL: I posted here as part of the project is a pen but please move if in the wrong place. This is one of those projects "designed", if I use the term loosely, on the back of an envelope and developed as it progressed. My granddaughter is an enthusiastic Harry Potter fan so I decided to...

Hi all, Does anyone know where to buy some ornamental hinges about 50mm x 30mm preferably black that would suit the lid of a treasure chest. Can't seem to fing what I want..... Cheers Frederick

Hi all, Sometime ago Derek (Dalboy) gave me an old and decommissioned green bowling ball made from Lignum Vitae. I started to turn it not sure how things were going to develope. It was so hard it put it to one side for a few weeks thinking that I will give it another try later on. I did start...

Hello all, Over the weekend I’ve been stabilising a number of blanks however noticed on the 2nd batch that the lid, which is 18mm Acrylic, had I thought cracked but after taking a closer look its only surface crazing on the underside. It seems ok although not sure I want to trust it for ever...

Last week's efforts. Took some time to do this as I was finding my way as not done much of these designs. The lid is Walnut, the cup I am not too sure of but could be Ash and the finial is from a scrap piece of Oak What I do like about this is that the lid fits properly. Not too tight...

Not done a hollow form for quite a while so thought about time I did another. Made from field maple for the main body, American black walnut for the top and beech for the finial. Was going to colour the finial but liked it the way it looked contrasting against the lid. The bottom has a little...

Another present made this time a box to keep some stamps in as well as a place for things like tweezers in the top tray. The lid is held in place by the top tray as I wanted the bottom to be quite shallow to make it easier to get the stamps out of the divisions. Made from an old shelf unit of...

Ive had my first customer message me with a problem with their pen and I have made and sold many - its a TM Kappa and it appears the threaded piece which is press fitted into the brass tube into which the section threads has come out of the brass tube. Has anyone else had this happen? Should I...

A couple of weeks ago I posted a pic of my very first box with lid and finial, (picture at the bottom) which is the Woodturning club challenge for Jan.. the nice comments suggested my finial was a bit small... So here is V2: Box with Lid and Finial... it’s going on show tomorrow night...

When I started this turning I really didn't know what I would end up with. Part way through turning I decided it was going to be a small box with lid. Unfortunately I don't have the patience to make a good interior finish, so now it is going to be a door knob. :-)) Resin & Pinecone Door knob -...

Well the day did not start that well first box the lid split I was a little heavy handed the second turned out Fine and the third I tried to make the lid smaller on the outside than the inside. As well as a couple of visitors nothing to do with woodturning.

I have been working on this in between doing other bits today that is after the one where the lid decided to do the splits. Made from London plane with a Laburnum insert in the lid it stands 2 3/4" X 2 1/4". Still need to make 4 more well there is always tomorrow. This is the longest I have...

I don't know whether to classify this as a bowl or a hollow form.

Just had the 20mm thick acrylic lid on our vacuum chamber shatter whilst stabilising some pen blanks, anyone have any suggestions on where we could purchase a piece of 30mm or even 40mm thick acrylic & have it machined? Not sure on trying to machine a piece myself as if it goes wrong it's a...

Fresh from the lathe... box from black locust, lid from mapple. Still some work on it for the finish

Just finished this piece. Polished with Carnauba wax.