sander

I thought it was about time I turned something so dug this wood out from the pile a little disappointed as it took me two hours to turn need to turn more. Finished with sander sealer and woodwax22 size is 6" X 1 3/4".

I have only used carbide tools for pen turning, but recently swapped an old mortiser for a box of rarely used lathe tools. What sharpening system do you use/recommend? I asked a neighbour who is doing a woodworking course at the local Tech what they used and he told me that the tutor only...

Does anyone use a belt sander in connection with pens. Trying to find out the use for one and any more ideas for their use to help me make my mind up if I should buy one. Advice please. Glen:face:

As any one used one of these to use on pens etc.

Fresh off the lathe Oak and ABW the knob is white acrylic 6" tall X 4" wide Pyrography outlines and finished with airbrush paints before acrylic sander sealer and satin lacquer photographed from both sides

Thought I would have another go at a piece of turning found what appeared to be a plain piece of ash in the woodpile, pleased with what I found inside. Finished with sander sealer and then put on my buffing system, I did add a coat of woodwax22 on top of that

Made this from Field maple burnt decoration then ebonised foot and finial finished with acrylic sander sealer followed by an acrylic satin finish

Finish one of two pieces should have the second finished either tomorrow or the following day. Still to give it a name. Inspired by Keith Tompkins from another site. The spiral is Yew and the base is Oak scorched and lime waxed. sealed with sander sealer and finished with woodwax22. Some very...

Rather than hijack Alan's thread on "squaring the end of pen blanks". Following a disscuion with Phil ( which I'm not tech enabled to copy over Phils reply?) As we know it is so easy to remove to much of the pen blank end, wether by a disc sander or barrel trimmer. I thought I'd try to rectify...

Two boxes turned today the spalted one was very punky so a good soak in thinned sander sealer and left to dry before turning did the trick along with some very sharp tools. Many people ask about turning punky wood and this shows it can be done. The second is American Black Walnut the lid it...

Had a couple of club members over for a chat and to go over different things so I turned this while they were here. London Plain finished with sander sealer and buffed with carnauba wax. Measures 8 1/2" X 1 1.2"

Straight out of the workshop, punky in places but have managed to harden them up with a good dose of sander sealer(see last photo). Made from Walnut it has so much going on in the grain even some light feathering Finished with sander sealer and then buffed on a three wheel system

Anybody looking for a small disc sander? Might be big enough to sand your pen blank ends? L.S. BARKER 30DS MOTORIZED DOUBLE ENDED VERTICAL ORBITAL SANDER. SN: 6960. NOTE: HARDWIRED. REQUIRES ELECTRICIAN TO DISCONNECT. - Price Estimate: AU$ - AU$ also for sale a small B/Saw. L.S. BARKER...

Getting ready to do a turning demo and was going to take the rough turned piece to work on so in preparation I started by returning the tenon and just take enough off to take out any wobble but found that it was tearing out something terrible so decided to complete it and find another one to...

I got fed up of using a large disc in the lathe to clean up the ends of my pen blanks OK OK I know I don't make that many anyway I always ended up usin just the centre and my decicated disc belt sander does not have a large enough table to make something for that. So a little while ago I had to...

Any ideas on where to get a new drive belt for my Titan Disc/Belt sander TTB045 BTS. Thanks in advance.

Multi purpose end squaring blanks for different kits. Pic 1 overall location of the Sander, mounted on an old Woodfast lathe bed. Use the sander on the shaft of the old lathe for general purposes. Fitted a new velcro fastened 120 grit to the Sander using a sheet of non stick between in situ...

A while ago I asked what can I use this old drill for, Note the brown stuff that grew on it after we had unseasonable rain that coming in near horizontally, the first time since I built the veranda onto my shed. A bit of a clean up. I made a spindle sander like Dereks. Now I keep...

Im always looking for ways to save Money as you do one was the vacuum chuck i shared a while ago now its a power sander see what you think As you can see its an old hand blender With a screw driver bit to take the various sized Sanding heads you could also fit a flexible shatf If you...