• Thanks for visiting The Penturners Forum today.

    There are many features and resources that currently you are unable to see or access, either because you're not yet registered, or if you're already registered, because you're not logged in.

    To gain full access to the forum, please log in or register now. Registration is completely free, it only takes a few seconds, and you can join our well established community of like-minded pen makers.

A query

Tom.1946

Graduate Member
Joined
Jul 18, 2021
Posts
624
Location
Northern Ireland
First Name
Tom
Happy new year to all
However a question
You have cut, drilled and glued etc..
I have seen turners making bowls etc, and they apply sand and sealer and polish etc by having the lathe stopped and apply with them on a cloth. Question is should you use the same method or apply with the lathe running???
 

flexi

Executive Member
Joined
Sep 12, 2014
Posts
6,612
Location
Maidstone
First Name
mark
There is no right or wrong with this....
Personally, Melamine I apply hand turning the lathe, but buff with the lathe..
CA I apply with the lathe running on slow then cut back on a medium speed...
What your trying to avoid is splatter and your own safety being compromised :think:
 

howsitwork?

Graduate Member
Joined
Sep 18, 2019
Posts
659
Location
north york (gods own county)
First Name
Ian
There is no right or wrong with this....
Personally, Melamine I apply hand turning the lathe, but buff with the lathe..
CA I apply with the lathe running on slow then cut back on a medium speed...
What your trying to avoid is splatter and your own safety being compromised :think:
Totally agree Mark

I flow melamine on from a fine soft brush on pens and a larger soft brush on small bowls.

I apply danish oil or tung oil using a soft cloth ( or white tissue ) but have started using a brush for that too ( with danish oil) the. immediately cleaning the brush in hot water with detergent. I tend to apply the initial coat with lathe off then subsequent coats with slow speed lathe. Speed n ease , the original easy to apply polish , I was taught to apply at slow speed from a cloth then speed up to polish with a different cloth. This avoided “lines” of polish on the work which then had to be “rubbed off”.

As for CA I apply using polythene ( of the end of my nitrile glove ) and wipe along then get my finger off before it sticks but that’s only on pens and to be honest I’m not that impressed by it compared to melamine.
 

Tom.1946

Graduate Member
Joined
Jul 18, 2021
Posts
624
Location
Northern Ireland
First Name
Tom
Unfortunately I don't have the luxury of a lathe with variable speed. So as Flexi said apply to wood and slowly buff. Then turn lathe on and buff further.
 

Dalboy

Executive Member
Joined
Mar 20, 2014
Posts
7,730
Location
Kent
First Name
Derek
I apply with the lathe stationary using a soft tissue to apply first a sealer then the top coat (Allowing to dry between coats). I apply it along with the grain. When I apply each coat I turn on and buff with the lathe running and sand between each coat with a very fine paper just enough to give a key for further coats
 

21William

Fellow
Joined
Jan 21, 2016
Posts
1,670
Location
Dorset
First Name
William
Hmm, Melamine. I bought a tin of this some time ago but not used it yet. Please remind me of some good reasons for using this stuff apart from Pens? It’s probably a few years old, will it still be any good?
 

Phil Dart

Moderator
Executive Member
Joined
Nov 28, 2014
Posts
5,534
Location
Colebrooke, Devon
First Name
Phil
Hmm, Melamine. I bought a tin of this some time ago but not used it yet. Please remind me of some good reasons for using this stuff apart from Pens? It’s probably a few years old, will it still be any good?
If it's unopened, it will probably still be OK. If it has been opened, you may find you need to add a drop of thinners, but it sshould still be OK
 


Write your reply...
Top