• Thanks for visiting The Penturners Forum today.

    There are many features and resources that currently you are unable to see or access, either because you're not yet registered, or if you're already registered, because you're not logged in.

    To gain full access to the forum, please log in or register now. Registration is completely free, it only takes a few seconds, and you can join our well established community of like-minded pen makers.

Italian Acrylic and Ivy Urn Clip

Gregory Hardy

Graduate Member
Joined
Jul 7, 2017
Posts
454
Location
Upper New York State
First Name
Greg
So…sometimes accidents happen… fly-by-the-seat-of your pants…and look at this. Italian acrylic with burgundy accent acrylic. Bock #6. The clip is my take on Grecian urn ivy – in a former life, I did this with pearl in guitar headstocks. Clip is primarily bronze with nickel vine and bronze leaves. Even the primary critic and chief bottle-washer (my wife, the Jewel-Without-A Flaw-To-Whom-I-Am-Married, She Who Is Without Fault) could only say, "Oh, my God, Greg..." and walked away. Must be a good one this time.
 

Attachments

  • 1.1.jpg
    1.1.jpg
    39.1 KB · Views: 73
  • 1.2.jpg
    1.2.jpg
    78.7 KB · Views: 144
  • 1.3.jpg
    1.3.jpg
    71.8 KB · Views: 70

Gregory Hardy

Graduate Member
Joined
Jul 7, 2017
Posts
454
Location
Upper New York State
First Name
Greg
Wow that looks amazing Greg, did you actually make the clip aswell?

I did make the clip, Paul. It's all laid up and soldered from pieces of bronze and nickel silver. The clip blade, clip rings, and ivy leaves were cut from bronze sheet and the vine was done with pieces of nickel half-round wire (a couple of different gauges). Keeping pieces in place in order to solder was a lot like trying herd cats - another hand (or two or three) would have been really helpful! Thanks again.
 

Bucks

Fellow
Joined
Apr 26, 2016
Posts
1,425
Location
North Yorkshire
First Name
Paul
I did make the clip, Paul. It's all laid up and soldered from pieces of bronze and nickel silver. The clip blade, clip rings, and ivy leaves were cut from bronze sheet and the vine was done with pieces of nickel half-round wire (a couple of different gauges). Keeping pieces in place in order to solder was a lot like trying herd cats - another hand (or two or three) would have been really helpful! Thanks again.

Wow you are a man of many talents. :drool:
 

Barry

Graduate Member
Joined
Nov 9, 2014
Posts
576
Location
shropshire
First Name
Barry
This pen shows I think that the pen of the week should be split into two categories Acrylic and Wood pens
There are some beautiful woods out there But acrylic is what ever the mind conjures up:thinks::thinks::thinks::thinks::thinks:
 

Gregory Hardy

Graduate Member
Joined
Jul 7, 2017
Posts
454
Location
Upper New York State
First Name
Greg
This pen shows I think that the pen of the week should be split into two categories Acrylic and Wood pens
There are some beautiful woods out there But acrylic is what ever the mind conjures up:thinks::thinks::thinks::thinks::thinks:

I'm not sure I agree. Every member of the forum has a list of things he or she looks for in "the perfect pen." Some folks are dazzled by a beautiful piece of wood, while others are more affected by a different material or process or technique. It's fun to see what catches the eye of each voter, and the surprise attached to the voting results. (Sometimes I am shocked!) I think the new process for selecting POTW is worth testing for a while longer without any additional strings attached.
 

silver

General dogsbody
Executive Member
Joined
Jun 29, 2013
Posts
6,304
Location
Somewhere in Staffordshire,
First Name
Eamonn.
one great looking pen Greg. it shows through your skills and quality of workmanship to a tee.

Keep up the good work as I like to see your pens mate.
 
Warning! This thread has not had any replies for over a year. You are welcome to post a reply here, but it might be better to start a new thread (and maybe include a link to this one if you need to).
Top