bullet

This is number 5 of 6 RAF centenary pens made with 338 spent bullet cases

Three bullet and acrylic pens for my friends in a local gun club. Having problems with ic orientation again..... :funny:

Had loads of orders for the Denya wood pens sierras and Omega's I also dressed more in them in Carribean pine also a bullet pen with Military ply put it on a flash auction for this evening

I am new to this forum, my name is Svein Viland and I am located in Norway. My aim is to find the required parts for making pens from bullet cartridges, and in particular .50 cal (12.7mm). Is there anybody in this group that can recommend the required parts (except the cartridge) and where to...

I do .308 bullet pens and a guy that bought 2 asked if I could make one from his .243 cases, I knew the slimline would need some jiggling about as the 7 mm tube wont fit through the .243 or 6mm, the guy sent me some antler as I had suggested he send me a case and antler from a stalking trip he...

Hi all, my efforts with slimlines..... We have a Queensland hairy Oak and two Spectra ply ones, one with a .223 bullet case and new bullet nib....

Hi All....I had a request from another turner....can you make a pen from 1 bullet case?.....well yes if it's big enough.....but it wasn't. Thinking cap on!!.....the solution is below.....extend the case with an infill.....this is only a prototype so improvements will be made.....it's fitted with...

Hi all.....some may know i have a couple of weakneses........Mik lawrence blanks....Toni randsfield blanks and bullet pens.....not nessaseraly in that order..... Well thanks to Les i found some bullet heads for my .500NE cases (£4 each!!)and after a quick chat scored these....yet more cases.....

Antler marrow on a HSM .338 Lapua Magnum once fired casing with a Hornady Match .338" 285 gr Boat Tail Hollow Point bullet drilled out to accept a Cross refill. Les

As the title two bolt action kits with the other halves from the blanks I made the bullet pens from

I have downloaded the instructions from the Tutorials section for making Firearms pens. I have laid out the parts and it appears the lower section ie. the bullet and the case will be shorter that the 7mm tube. This means the 7mm tube will be sticking out the end of the bullet case which in turn...

I use DeWalt bullet point drills and like them a lot. I find they don't wander as easily and tend not to chip out the bottom as much. I would like to use them for my new foray into turning pens. I'm having trouble finding the difinitive drill set for pen turning. Metric sizes seem to be an...

2 camo .303 bullet pens & 1 camo .308 bullet pens. The camo blanks are bamboo & along with the cartridges they were donated by our Lonz. Thanks Bob for your generosity.

Hi, I made my first bullet pen today :-) Although I polished with Brasso, I am sure it will eventually tarnish/discolour :-( Is it possible/worthwhile applying a finish that keeps the shine? I read about 'Everbrite' but it is American and is it suitable? Advice please would be great :-) TIA...

Well it may be old hat to some but i am giving it a go.... Some may know i like to play with bullet cases and have had reasonable success....but i am now trying to do bullet case pens from scratch.....using once fired brass cases and real bullet heads I have always bought things to make these...

Pen that was made a little while ago for a newly appointed Warrant Officer. Blank - Military Ply Kit - TB chrome bullet Finish - CA Engraving done with a laser engraver, then returned to the lathe for the CA finish. You cant actually feel where its been engraved.

Dave Green from Turners Retreat 247smiler gave away a few of the pens that they market. I was lucky enough to get the Cartridge Bullet Pen from him. Sorry its taken so long for me to get around to making it Dave :sob: This is a well made kit with a good fit of all the component parts and a...

Not every ones favourite kit but I like it and it sells well in fact bullet pens are my best sellers

Made up the last of my 308 bullet pens today made using military ply and two in plastic they are all going to horseback and this is my lot for 2016

So I've been casting PR for a couple of months with so great results but I was getting annoyed at how brittle it was (I need a more robust product). So I bit the bullet and bought a pressure pot, compressor along with some clear polyurethane resin and a shed load of mica colors I feel like a...