• Thanks for visiting The Penturners Forum today.

    There are many features and resources that currently you are unable to see or access, either because you're not yet registered, or if you're already registered, because you're not logged in.

    To gain full access to the forum, please log in or register now. Registration is completely free, it only takes a few seconds, and you can join our well established community of like-minded pen makers.

tube

  1. B

    acrylic

    Has anybody purchase a box of these 5kg Box European Pen Blank Offcuts - Special Offers Are they value for money or too short to use for much- I am hoping to use them on single tube pens, unless I get lucky and there are any pieces that I can squeeze 2 out of.
  2. D

    CA Glue - Thin or Medium

    Apologies if I am asking an old question. Does anyone have a preference when using CA to glue in the brass tubes. I tried using medium today as I could see more of a gap between the blank and the brass tube, but I found it lessoned the movement of the brass tube going in the pre drilled hole...
  3. H

    Pen rotisserie?

    I have been experimenting with carbon fibre pen blanks and decided to try painting on resin to seal them, but I didn't fancy turning the tube by hand until the resin had set, so I made this jig to do it for me! Questions and comments welcome.
  4. sammy

    Which glue

    Is there a simple one tube glue for sticking tubes in blanks. I tried ca but had a couple of disasters when it set before the tube was in the right place. So I tried epoxy but trying to get two equal amounts out of the tubes is a pain, even with one of those twin tube jobbies. What glue do you...
  5. hawkeyefxr

    Youtube Videos

    I have been trawling through the Tube looking at videos and have come across a guy called Chris Stott. The video quality is awful at 360 and the sound sync is way off, but, for me his presentations of things is really good. I am talking about someone just starting like myself. He shows real...
  6. angelo49

    Braided Elegant, Thanks Les

    As per Braided Pen Tutorial by Les. I used a 12mm x 10' cheap vinyl tube bought on ebay. After fitting it to the prepared tube, holding it taught, I soaked it in CA, wiped it down with plastic bag, and lightly sprayed accelerator. I did this about 4 times. I wanted to see if the vinyl would have...
  7. Simone

    My first try at Steam Punk

    My first attempt at Steam Punk. I Planned to make 4 but only 3 made the cut .When I assembled the first one the internal pressure was too much (think i did not clean the tube inside :thinks:) and you could see the Resin separate from the tube. I cast these in Polyester Resin, serious smelly...
  8. P

    Calling Manchester

    Hi There, I was wondering if there are any kind members in the Manchester area give or take 10 miles who would be so kind as to show me how they turn pens. I've watched dozens of videos on You Tube but you can't beat seeing it in the flesh as they say. Any help would be greatly appreciated...
  9. P

    Playing with hexagonal blanks

    Hi all! For a Vertex, one hex kit from PSI, I choose a piece of hard wood that I turned a bit oversized. I drilled it, draw some lines and with a hand plane I made a nice hexagonal blank. Then I dipped it for 2 hours in boiling water. After having prepared a tube, I took the blank out of the...
  10. P

    Bedroom Dust Extraction

    Further to my last post I've been doing some research on a good household vacuum with decent suction and this one may fit the bill. The Henry Xtra HVX 200A2 The You Tube reviews are very good and the additional acessories will come in handy. I would be interested in your opinion as it seems my...
  11. Freck Fraser

    Mistral FP in a Pine Cone Hybrid Blank

    Today saw me start the most "erse clenching" order to date, after an old workmate wanted 4 "high end" fountain pens. After discussing the build options with him he chose Mistrals from "Beaufort Ink" and a variety of hybrid blanks from George Watkins over at "From The Tree". As I'm new to this...
  12. hawkeyefxr

    Brass tubes and bushing fits

    I have noticed that some bushing kits fit better than others, what should be the clearance when the bushing is inserted into the brass tube. Obviously if it's to loose you will have all sort of problems, if it's tight you will maybe expand the brass tube and wreck the pen before you get going.
  13. angelo49

    Drilling Acrylic/Resin Blanks

    When drilling these blanks there is always the risk of a blow out when the drill exits thru the bottom of the blank. FOR ME IT'S ABOUT 90%, NO MATTER WHAT DRILLS I USE. So I cut the blank much longer than needed and drill past the tube length. Then cut the blank to length and you end up with a...
  14. Woody

    For our barmaid

    Lisa our barmaid is leaving so I made this for her but I'm not happy with it I made up several blanks at the same time and some of them had glitter in and some of it has gotten on the tube of this one also I used pearlescent paper and I'm not happy with that so I shall make another one tonight
  15. Chillicamper

    Slight accident with a Mistral

    I thought I'd treat myself and try out a the Mistral kit I have to say it's a high end kit, beautifully smooth to put together. The wood is FiddlebackTasmanian Blackwood. Whilst turning it became evident that there was a fault in the wood - drilling it has seems to hit a softer spot, but I'd...
  16. S

    Steampunk.

    Commissioned last year for a real steampunk fan, he was over the moon. The time to dress the tubes alone took me four and a half hours. This was a bit less trouble.
  17. T

    bullet

    Nearly wrecked this one assembled it without click mechanisim ended up with the inner tube seperated but anaged to glue it back together
  18. pittswood

    New Beaufort Mistral ballpoint pen

    Hi guys, As we all know, Phil from Beaufort Ink has been developing his new ball point and pencil kit. I was given the pleasure of turning the ballpoint pre-development kit this week. As no pen bushing are available yet, this pen was turned on nylon cones I made myself, out of 20 mm white HDPE...
  19. Winemaker

    Classic Elite Fountain Pen

    Just made (well tried) to make a Classic Elite Fountain Pen for the first time, the Instructions show 7 mm bushings and there are 7 mm bushings in the kit, fine of I go without checking the tube size, drill the blanks with a 10 mm drill glued the tubes in to the blanks put it all on the...
  20. flexi

    TM Alpha

    Hi all this is the 1st of my next batch from Mik Lawrence. This was a request by a customer, Mik did cast it for a jnr gent 2 but i fitted it to an Alpha instead....the bottom tube is 5 mm longer and the top seemed good....its also now got a Bock 1.9 italic fitted...i have had so many...
Top